联系我们
公司名称：XXX
电话：XXX
手机：XXX
联系人：XXX
地址：XXX
新闻动态
晶面光亮剂使用方法
1、先确保地台清洁干爽，确保石材表面的洁净。清除地表原有的蜡及污物，如石面粗糙可翻新 到2000-3000#。混凝土地坪, 水磨石地坪须用树脂磨片粗磨、细磨至2000-3000#
1. First, make sure the floor is clean and dry, and the stone surface is clean. Remove the original wax and dirt on the surface. If the stone surface is rough, it can be renovated to 2000-3000 m3. Concrete floor and terrazzo floor shall be roughly and finely ground to 2000-3000 with resin grinding plate#
2、选用0#—2#钢丝.把钢丝盘绕到晶面机的针盘上，钢丝棉要盘绕平整,均匀,方向要顺时针盘,如果针盘上的针比较长的，可在两者之间加放一片百洁垫，以保护针盘。
2. Use 0 × 3-2 × steel wire to coil the steel wire to the needle plate of the crystal face machine. The steel wire cotton shall be wound flat and even, and the direction shall be clockwise. If the needle on the needle plate is relatively long, a cleaning pad can be placed between the two to protect the needle plate.
3、选用专用晶面拋光处理机或刷地机（转速145—175 转/分钟）。
3. Select special crystal surface polishing processor or ground brush machine (speed 145-175 RPM).
4、在1-2平方米的地面上喷洒少量晶面光亮剂，把晶面抛光机快速移至地面打磨均匀，再左右来回细细地打磨干燥，直至光亮有水晶镜面效果即可，如效果不满意可重复一次。
4. Spray a small amount of crystal Brightener on the ground of 1-2 square meters, quickly move the crystal polishing machine to the ground and polish it evenly, and then polish and dry it carefully from left to right until there is crystal mirror effect. If the effect is not satisfactory, repeat it.
1. First, make sure the floor is clean and dry, and the stone surface is clean. Remove the original wax and dirt on the surface. If the stone surface is rough, it can be renovated to 2000-3000 m3. Concrete floor and terrazzo floor shall be roughly and finely ground to 2000-3000 with resin grinding plate#
2、选用0#—2#钢丝.把钢丝盘绕到晶面机的针盘上，钢丝棉要盘绕平整,均匀,方向要顺时针盘,如果针盘上的针比较长的，可在两者之间加放一片百洁垫，以保护针盘。
2. Use 0 × 3-2 × steel wire to coil the steel wire to the needle plate of the crystal face machine. The steel wire cotton shall be wound flat and even, and the direction shall be clockwise. If the needle on the needle plate is relatively long, a cleaning pad can be placed between the two to protect the needle plate.
3、选用专用晶面拋光处理机或刷地机（转速145—175 转/分钟）。
3. Select special crystal surface polishing processor or ground brush machine (speed 145-175 RPM).
4、在1-2平方米的地面上喷洒少量晶面光亮剂，把晶面抛光机快速移至地面打磨均匀，再左右来回细细地打磨干燥，直至光亮有水晶镜面效果即可，如效果不满意可重复一次。
4. Spray a small amount of crystal Brightener on the ground of 1-2 square meters, quickly move the crystal polishing machine to the ground and polish it evenly, and then polish and dry it carefully from left to right until there is crystal mirror effect. If the effect is not satisfactory, repeat it.
